Roomba Not Charging: Best 10 Ways 2023

Q: How do I reset my Roomba battery?

Take the following steps: 1. Press the CLEAN button for your Roomba to turn ON . 2. For 10 seconds, simultaneously press and hold the SPOT and DOCK buttons. 3. In response to the familiar Roomba sound, simultaneously release both buttons. 4. Plug your robot into a socket and give it at least 2 hours to charge. You'll notice that the CLEAN button has changed to green light after 2 hours.

Q: How many years do Roomba batteries last?

Your Roomba will typically run for two hours or so before returning to the home base to recharge. If notice the flashing red light, it means the device's battery isn't charged enough to run a mission and needs a little more time. Usually, it takes at least two hours for it to charge . Removing the battery when you aren't using your Roomba or while you are away is a fantastic additional strategy to prolong Roomba's battery life! Such factors as the model you have, how frequently you use the item, and the types of surfaces in your home crucially affect how long a Roomba battery lasts. If you have a lot of carpets, your robot vacuum will work more and thus deplete its charge more quickly. It will also have to work harder to remove dust in houses with plenty of pet hair. However, if you use it properly,the authentic iRobot battery can survive more cleaning cycles than most other robot vacuums. Approximately, it is 400 cleaning cycles. Every one to two years, you will need a replacement battery.

Q: What do you do if your Roomba won't charge?

Make sure to plug the wire in properly .Try doing that by unhooking the cord and replugging it if necessary. Try using a different power outlet .It can appear to be a simple task. However, plugging the device into a different outlet is the most typical way to get it recharged. Next, make sure nothing is obstructing the connection in the docking station.Start by inspecting it. If there is an obstacle, remove it and try once more. Check Roomba's charging contacts on dirtiness .The vacuum's charging contacts might not be fully cleaned for making a proper connection. If that is your case, then use a Q-tip dipped in rubbing alcohol to clean them. Finally, you might need to replace the battery .If you see that Roomba still won't charge, you probably will have to get a new battery for your robot. The problem may have occurred during shipping .You should first open the battery compartment and check whether the battery is displaced. If so, try removing the battery and replacing it correctly in the same location.

One of the most irritating household chores is likely vacuuming. But not with an iRobot Roomba!

This tiny but powerful robotic helper with its rechargeable battery will easily replace an ordinary vacuum cleaner by completing all of the work for you!

Unfortunately, according to customer reviews, one of the most frequent issues with this item is that it is not charging properly or at all.

In precisely this article we will give you tips on to handle this situation: roomba not charging.

Red color light: is Roomba charging or not?

If the red color is animated and moving around the CLEAN ring, it means the dirt bin of your machine is full.

Roomba will also flash red if the battery is too low when you try to start a cleaning cycle.

However, if you see a solid red light that doesn’t pulse or move, Roomba tries to deliver you an error message: something is wrong with your robot.

10 ways to fix Roomba’s charging problem

Clean charging contact points

The charging points may corrode or grow dusty over time, which will prevent the Roomba from being charged properly.

To clean these charging points, just use a cotton swab or a dry cloth or Q-tip bathed in rubbing alcohol. After that, gently wipe the

charging contacts.

Clean the Charging Station

Due to its poorly sufficient power supply, sometimes a Roomba can bring with it the dirt that gets stuck onto the charging ports of the station.

Use rubbing alcohol and a soft cloth (or a microfiber cloth) to clean the station.

Reset the Roomba

Try doing a soft reset by holding down the buttons CLEAN and DOCK at the same time until you hear a beep.

To start the Roomba on the 500 series, you must hit CLEAN.

The clean light will then dim and you will hear a chime if you continue to hold down the SPOT and DOCK buttons simultaneously.

After doing the reset, you may plug the charging wire into your Roomba.

Allow your Roomba to charge for 72 hours until the power light becomes green.

The green light turning on is indicating that the battery is fully charged.

Fix the position of the battery

The battery could have moved from its original location during shipping.

Simply remove the Roomba’s five screws to access the battery compartment and adjust the position of every battery. Ensure that the batteries are installed properly.

Use another outlet

Try plugging your Roomba into another outlet.

The outlet you’re using might not be functioning properly. Check to see if it works by plugging something else into the outlet. If it does, the outlet is most likely not the issue.

Replace the dock

The docking station may be broken, which would explain why the Roomba isn’t receiving enough electricity to charge.

Get a replacement dock if the Roomba is still not charging.

Perform a factory reset

In case a soft reset doesn’t work, you can try a factory reset.

Your Roomba will return to its factory settings after you take this action.

You should first make a backup of your data because a factory reset will remove any customized settings that are saved on the Roomba.

Keep holding down the button CLEAN for 10 seconds to execute a factory reset.

Release the button once the indicator light begins to flash, and the Roomba should restart.

Replace the battery

If none of the previously mentioned fixes succeed, your battery likely has to be repaired or replaced.

Clean the caster wheel

The caster wheel works to maintain the robot at the right height and leave enough room beneath the appliance for it to sweep up dirt and dust.

Every time your robot cleans, dust accumulates on it.

The wheel is pushed farther from its housing as the debris builds up, which makes it rise higher.

The Roomba’s charging points won’t get to the Home Base’s contact points if the caster wheel is raised.

The device won’t be able to recharge itself as a result.

So, clean the wheel on your Roomba and see whether the issue is resolved.

Contact iRobot customer care

You should get in touch with Roomba customer support if none of the fixes seem to work.

To connect with other users who had similar problems with Roomba, you can also read the community forums.

FAQ

How do I reset my Roomba battery?

Take the following steps:
1. Press the CLEAN button for your Roomba to turn ON.
2. For 10 seconds, simultaneously press and hold the SPOT and DOCK buttons.
3. In response to the familiar Roomba sound, simultaneously release both buttons.
4. Plug your robot into a socket and give it at least 2 hours to charge.
You’ll notice that the CLEAN button has changed to green light after 2 hours.

How many years do Roomba batteries last?

Your Roomba will typically run for two hours or so before returning to the home base to recharge.
If notice the flashing red light, it means the device’s battery isn’t charged enough to run a mission and needs a little more time.
Usually, it takes at least two hours for it to charge.
Removing the battery when you aren’t using your Roomba or while you are away is a fantastic additional strategy to prolong Roomba’s battery life!
Such factors as the model you have, how frequently you use the item, and the types of surfaces in your home crucially affect how long a Roomba battery lasts.
If you have a lot of carpets, your robot vacuum will work more and thus deplete its charge more quickly.
It will also have to work harder to remove dust in houses with plenty of pet hair.
However, if you use it properly,the authentic iRobot battery can survive more cleaning cycles than most other robot vacuums.
Approximately, it is 400 cleaning cycles.
Every one to two years, you will need a replacement battery.

Why won’t my Roomba turn on or charge?

First of all, it is worth noting that a new iRobot Lithium-Ion Battery must be woken up on the Home Base before its first use.
If you didn’t skip that step and did everything else correctly when turning your Roomba for the first time, there may be other reasons for it not to work properly:
– Your Roomba’s battery may be completely dead.
– Your Roomba’s power cord may be damaged.
– The charging dock may be damaged.
– Your Roomba’s charging contacts might be dirty.
Besides that, such things as dirty metal contacts, misaligned docking stations, faulty power adapters, frayed charging cables, and faulty batteries are leading reasons Roomba won’t charge.

Roomba not charging: how to fix in seconds

There may be several reasons why your Roomba won’t charge.
The problem may be in the socket you’re using, in a displaced or damaged battery, or in a charging station. Charging contacts in your Roomba might be dirty, causing a poor connection.
In most cases, you can fix the robot yourself. You can experiment with simple fixes like using another outlet, cleaning the charging contacts, or restarting your Roomba.
If you see that none of your solutions seem to work, then it is time for you to contact iRobot customer care.

What do you do if your Roomba won’t charge?

Make sure to plug the wire in properly.Try doing that by unhooking the cord and replugging it if necessary.
Try using a different power outlet.It can appear to be a simple task. However, plugging the device into a different outlet is the most typical way to get it recharged.
Next, make sure nothing is obstructing the connection in the docking station.Start by inspecting it. If there is an obstacle, remove it and try once more.
Check Roomba’s charging contacts on dirtiness.The vacuum’s charging contacts might not be fully cleaned for making a proper connection. If that is your case, then use a Q-tip dipped in rubbing alcohol to clean them.
Finally, you might need to replace the battery.If you see that Roomba still won’t charge, you probably will have to get a new battery for your robot.
The problem may have occurred during shipping.You should first open the battery compartment and check whether the battery is displaced. If so, try removing the battery and replacing it correctly in the same location.

Conclusion

In case you’ve encountered a problem when your Roomba is not charging, we presented you with a list of possible solutions.

The issue may be solved by using another socket, examining the state of the battery, and replacing it if needed.

Try checking the docking station for any debris periodically: that may be blocking the connection.

If everything else fails, you can always get help from iRobot customer support.

We hope the answers above will help you quickly fix the issue affecting your robot!

We're an affiliate

We hope you love the products we recommend! Just so you know, CleanyHome.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by linking to Amazon.com.

Roomba not charging: 10 ways to make a quick fix

Red color light: is Roomba charging or not?