Tineco IFloor 3 Keeps Shutting Off

Tineco Ifloor 3 is one of the best products in the market and when it keeps shutting off then it is due to the following reasons

• Low battery power
• Problem in the water tank
• Dirty water tank
• Damaged brush roll
• Blockage in the vacuum suction

You can easily stop the Tineco IFloor 3 from shutting off by following the solutions we provide. For that, keep reading till the end. 

Why Does Tineco IFloor Keep Shutting?

Just like the a10 Max button not working, there are different reasons for the IFloor 3 shutting off. The following table demonstrates that. 

Problem	Solution
Low Battery	Charge the Battery
Water Tank Problem	Replace the Water Tank
Dirty Water Tank	Clean Water Tank, Clean HEPA Filter
Damaged Brush Roll	Clean the Brush Roll, Replace the Brush Roll
Blockage in the Vacuum Suction	Fix the blockage

Low Battery:

The Tineco iFloor 3 is built to switch off automatically when the battery is low. This is to stop it from getting too hot and getting damaged. If the battery isn’t charged or is running low, the vacuum might suddenly turn off.

Solution: Charge the Battery

Ensure that the battery is fully charged. Use the included proprietary Tineco adapter to charge the battery. The blue charging light should light up for more than 10 seconds to indicate proper charging.

The iFloor 3 has a battery life of up to 25 minutes in normal mode. If the battery is fully drained, it will shut down. To extend battery life, avoid deep cleaning or using the vacuum for extended periods without recharging. 

Water Tank Problem:

If the clean water tank of your iFloor 3 gets damaged or if the water gets too hot, it can cause problems. Also, if the dirty water tank gets completely full, the vacuum might stop working and show error messages saying “dirty water tank full,” even if it’s not really full.

Solution: Replace the Water Tank

Check the clean water tank to make sure it’s not damaged and that the water isn’t too hot (keep it below 60 degrees Celsius or 140 degrees Fahrenheit). If the tank is damaged, you might need to get a new one.

If you decide to replace the water tank then following are the steps.

Remove the Dirty Water Tank: Find the dirty water tank at the back of the iFloor 3. Press the release button and pull out the tank.

Detach the Clean Water Tank: The clean water tank is usually in the front. Press the release button and lift the tank out.

Install the New Clean Water Tank: Take the new clean water tank and line it up with the opening on the iFloor 3. Push it in until you hear a click.

Reattach the Dirty Water Tank: Put the dirty water tank back where it was. Push it in until it’s securely locked.

Check for Proper Installation: Make sure both tanks are properly in place and locked. The vacuum won’t work if they’re not fitted correctly.

Dirty Water Tank:

When hair, dirt, or other stuff blocks the dirty water tank, it can stop the water from draining properly. This might make the vacuum shut down, and you might see a message saying the “dirty water tank is full,” even if it’s not really full.

Also, if the sensors inside the dirty water tank get clogged with dirt, the vacuum might not work right and could shut down.

Lastly, if the HEPA filter gets dirty or clogged, it can also make the vacuum shut down.

Solution: Clean Water Tank

Following are the steps of cleaning the water tank. 

Step 1: Make sure the dirty water tank is completely empty to get rid of any dirt or stuff inside. 

Step 2: After that, use a brush with stiff bristles to scrub the walls and bottom of the tank really well. Pay extra attention to the corners and any spots that are hard to reach.

Step 3: Rinse the tank with fresh water to wash away any leftover dirt or debris.

Step 4: If the tank needs a deeper clean, you can use a solution with extra chlorine. Mix one part of the solution with two parts water and scrub the tank with it.

Step 5: Once the tank is clean, fill it up with fresh water again. This makes sure your vacuum works well and stays clean.

Solution: Clean HEPA Filter

HEPA filters are important. But you also need to keep the HEPA filter clean. Following are the steps of the process for washable filters.

Step 1: Take out the washable HEPA filter from your appliance, like an air purifier or vacuum cleaner.

Step 2: Gently tap the filter over a trash can to get rid of any loose dirt or debris.

Step 3: Under a gentle stream of water, rinse the filter until the water runs clear. Make sure only water touches the filter material, avoiding direct contact.

Step 4: Let the filter air dry for at least 24 hours to avoid any damage or issues with how it works.

For Non-Washable HEPA Filters:

Step 1: Take out the non-washable HEPA filter from your appliance.

Step 2: Use a vacuum cleaner hose with a brush attachment to clean the filter and remove any dirt. This is the best way to clean non-washable filters.

Step 3: Make sure the filter is totally dry before putting it back in place to prevent any damage or problems with performance.

Damaged Brush Roll

When the brush roller gets blocked with hair, dirt, or other stuff, it can stop the vacuum from sucking up dirt properly. This might make the iFloor 3 shut down to stop any damage.

Solution: Clean the Brush Roll

Following are the steps to clean the brush roll.

Step 1: Find the brush roller on your vacuum cleaner and take it off.

Step 2: Use a brush with stiff bristles or a vacuum cleaner attachment to get rid of any hair, dirt, or other stuff stuck on the roller.

Step 3: Inspect the brush roller for any cracks, tears, or bends. If you see any damage, you’ll need to get a new roller.

Step 4: Once the roller is clean and in good shape, put it back on the vacuum cleaner.

Solution: Replace the Brush Roll

However, cleaning alone doesn’t fix the brush roll issue then it is time to replace the brush roll.

Following are the steps of replacing the brush roll.

Step 1: Take off the old or broken brush roller from your vacuum cleaner.

Step 2: Get the new brush roller and line it up with the spot where the old one was. Push it in until it clicks into position.

Step 3: Make sure the new brush roller is in the right place and firmly locked in.

Bonus: Find out why the INSE vacuum brush is not spinning. 

Blockage in the Vacuum Suction Path

When things block the suction path, the vacuum can’t suck up dirt as well. This makes it hard for the iFloor to clean properly. If this happens, the vacuum might shut down to stop any damage or overheating. 

If the blockage is really bad, it can make the motor get too hot, and then the iFloor will shut down to avoid damage or electrical problems.

Solution: Fix the Blockage

Following are the steps to fix the blockage. 

Step 1:  Make sure the vacuum is unplugged to avoid any electrical problems while you’re fixing it.

Step 2:  Figure out where the blockage is in the vacuum. It might be in the vacuum head, hose, or where the hose connects to the vacuum.

Step 3 (i):  If it’s in the Head, turn the vacuum head over and check inside. Use your fingers or a tool to pull out the blockage. You might need to take apart the brush head to get it out completely.

Step 3 (ii): If it’s in the Hose, put one end of the hose in a garbage bag and use a mop pole or something similar to push the blockage out into the bag.

Step 3 (iii): If it’s in the Vacuum, feel around with your fingers to find the blockage and pull out as much as you can. For any remaining blockage, try using a small tool like an industrial pipe cleaner.

Step 4: Once you’ve cleared the blockage, plug in the vacuum and test it to make sure it’s working like it should.

Frequently Asked Questions (FAQs):

Why Does My Vacuum Shuts Itself Off?

Your vacuum shuts itself off all of a sudden due to a bad vacuum hose, clogged motor air filter or just a bad suction motor. If there is any tripped overload on the vacuum suction motor then it will get shut off during the vacuum cleaner use. If that’s the case then just find the reset button and push it. If it’s too warmed up then let it cool down. 

How Do You Fix a Tineco Dust Sensor Malfunction?

To fix a tineco dust sensor malfunction you have to clean the sensor and ensure that it is properly maintained. Start by just cleaning up the dustbin and the filters. After that, check to make sure that gaskets of mesh filter and dustbin lid are in the right place. Then remove any blockages from the dustbin inlet. Finally, clean the Tineco dust sensor itself. 

Why Does My Vacuum Overheat and Shut Off?

Your vacuum will overheat and shut off if there is any problem with the airflow. Once there is something that gets caught in the hose in another part of the system then the airflow is reduced. As a result, the overall vacuum gets overheated and then just shuts off. 

Conclusion

In conclusion, when a Tineco IFloor 3 keeps shutting off there are a lot of reasons. You should diagnose the problem properly and then get to the root of the solution. Only then you should proceed to fixing the problem. If you are not sure then it is always a good idea to consult professionals.